MasterFormat Division 35 – Waterway and Marine Construction in Construction Division 01 Guide: General Requirements

Start with the role-neutral [CSI MasterFormat Division 35: Waterway and Marine Construction](/MasterFormat-division-35-waterway-and-marine-construction) guide for the broad scope and coordination boundaries. The guidance below addresses the narrower construction division 01 guide: general requirements intent.

Division 35 in the Construction Division 01 Guide: General Requirements Workflow

Division 01—General Requirements—sets the administrative and procedural framework for the entire project. Every technical specification section depends on Division 01 for submittal procedures, quality requirements, temporary facilities, product requirements, and closeout procedures. When Division 01 articles don't align with technical section requirements, the result is ambiguity, RFIs, and disputes. CSI Dynamic Standards supports validation that technical sections' "Part 1—General" requirements are consistent with Division 01 articles. Within this workflow, Division 35 provides the section-level classification that keeps waterway and marine construction scope organized and traceable. Defines the Division 01 section structure—from Summary of Work through Closeout Procedures—that governs administrative requirements for the entire project.

The construction division 01 guide: general requirements workflow involves the following steps—each of which touches Division 35 data:

1. Step 1 — Structure Division 01 using authoritative MasterFormat sections for administrative requirements For Division 35, this means waterway and marine construction sections must be correctly numbered, titled, and cross-referenced at this stage.
2. Step 2 — Cross-reference Division 01 articles to technical section requirements for consistency For Division 35, this means waterway and marine construction sections must be correctly numbered, titled, and cross-referenced at this stage.
3. Step 3 — Validate that technical sections' Part 1—General references align with Division 01 provisions For Division 35, this means waterway and marine construction sections must be correctly numbered, titled, and cross-referenced at this stage.
4. Step 4 — Ensure submittal, QA, product, and closeout procedures are consistent project-wide For Division 35, this means waterway and marine construction sections must be correctly numbered, titled, and cross-referenced at this stage.

Key Division 35 Sections in Construction Division 01 Guide: General Requirements

The following Division 35 sections are most frequently referenced during construction division 01 guide: general requirements:

• 35 20 00 – Waterway and Marine Construction and Equipment
• 35 30 00 – Coastal Construction
• 35 40 00 – Waterway Construction and Equipment
• 35 50 00 – Marine Construction and Equipment
• 35 70 00 – Dam Construction and Equipment

These sections must be current and consistently referenced throughout the construction division 01 guide: general requirements process. A single outdated section number in a construction division 01 guide: general requirements deliverable can trigger RFIs, scope disputes, and rework downstream.

Who Does Division 35 Work in This Workflow

• Specification writers authoring Division 01 — engages with Division 35 – Waterway and Marine Construction sections during construction division 01 guide: general requirements to ensure waterway and marine construction scope is correctly classified and coordinated.
• Project managers reviewing spec completeness — engages with Division 35 – Waterway and Marine Construction sections during construction division 01 guide: general requirements to ensure waterway and marine construction scope is correctly classified and coordinated.
• Architects ensuring drawing-to-spec coordination — engages with Division 35 – Waterway and Marine Construction sections during construction division 01 guide: general requirements to ensure waterway and marine construction scope is correctly classified and coordinated.
• Contractors reviewing project requirements before bidding — engages with Division 35 – Waterway and Marine Construction sections during construction division 01 guide: general requirements to ensure waterway and marine construction scope is correctly classified and coordinated.

These professionals depend on accurate Division 35 data to produce deliverables that align with the project manual and avoid classification conflicts across disciplines.

How Standards Support Division 35 in Construction Division 01 Guide: General Requirements

Construction standards govern how Division 35 sections are organized, cross-referenced, and maintained within the construction division 01 guide: general requirements workflow:

MasterFormat — Defines the Division 01 section structure—from Summary of Work through Closeout Procedures—that governs administrative requirements for the entire project.

SectionFormat — Ensures each Division 01 section follows consistent Part 1/Part 2/Part 3 structure where applicable.

Division 35 Cross-References

UniFormat: Division 35 extends UniFormat into marine and waterway infrastructure—specialized construction entities beyond typical building scope.

OmniClass: OmniClass Table 11 (Construction Entities) classifies marine and waterway facilities as built environment entities.

These governed relationships ensure that Division 35 data stays aligned with element classifications and lifecycle tags throughout the construction division 01 guide: general requirements workflow. When cross-references break, coordination failures multiply across every trade and discipline that touches waterway and marine construction work.

CSI Dynamic Standards for Division 35 in Construction Division 01 Guide: General Requirements

CSI Dynamic Standards includes Division 35 as part of a connected, edition-aware classification system—licensed through The Construction Standard. For teams executing construction division 01 guide: general requirements, this means always-current Division 35 section numbers and titles, governed cross-references to UniFormat and OmniClass, and edition tracking that prevents the classification errors that cascade through construction division 01 guide: general requirements deliverables. Instead of manually verifying that Division 35 references are up to date at each workflow step, teams get a single source of truth that stays current across every project.