MasterFormat Division 06 – Wood, Plastics, and Composites in Construction Division 01 Guide: General Requirements
How MasterFormat Division 06 – Wood, Plastics, and Composites fits into the construction division 01 guide: general requirements. Workflow steps, standards governance, and CSI Dynamic Standards.
Quick answer
MasterFormat Division 06 – Wood, Plastics, and Composites is integral to the construction division 01 guide: general requirements workflow. Division 06 covers rough carpentry, finish carpentry, architectural woodwork, structural plastics, and composite assemblies—wood-based and engineered framing, millwork, and casework. When teams execute construction division 01 guide: general requirements, Division 06 sections define the scope, products, and execution standards that must be accurately classified at every step.
Start with the role-neutral [CSI MasterFormat Division 06: Wood, Plastics, and Composites](/MasterFormat-division-06-wood-plastics-and-composites) guide for the broad scope and coordination boundaries. The guidance below addresses the narrower construction division 01 guide: general requirements intent.
Division 06 in the Construction Division 01 Guide: General Requirements Workflow
Division 01—General Requirements—sets the administrative and procedural framework for the entire project. Every technical specification section depends on Division 01 for submittal procedures, quality requirements, temporary facilities, product requirements, and closeout procedures. When Division 01 articles don't align with technical section requirements, the result is ambiguity, RFIs, and disputes. CSI Dynamic Standards supports validation that technical sections' "Part 1—General" requirements are consistent with Division 01 articles. Within this workflow, Division 06 provides the section-level classification that keeps wood, plastics, and composites scope organized and traceable. Defines the Division 01 section structure—from Summary of Work through Closeout Procedures—that governs administrative requirements for the entire project.
The construction division 01 guide: general requirements workflow involves the following steps—each of which touches Division 06 data:
- Step 1 — Structure Division 01 using authoritative MasterFormat sections for administrative requirements For Division 06, this means wood, plastics, and composites sections must be correctly numbered, titled, and cross-referenced at this stage.
- Step 2 — Cross-reference Division 01 articles to technical section requirements for consistency For Division 06, this means wood, plastics, and composites sections must be correctly numbered, titled, and cross-referenced at this stage.
- Step 3 — Validate that technical sections' Part 1—General references align with Division 01 provisions For Division 06, this means wood, plastics, and composites sections must be correctly numbered, titled, and cross-referenced at this stage.
- Step 4 — Ensure submittal, QA, product, and closeout procedures are consistent project-wide For Division 06, this means wood, plastics, and composites sections must be correctly numbered, titled, and cross-referenced at this stage.
Key Division 06 Sections in Construction Division 01 Guide: General Requirements
The following Division 06 sections are most frequently referenced during construction division 01 guide: general requirements:
- 06 10 00 – Rough Carpentry
- 06 20 00 – Finish Carpentry
- 06 40 00 – Architectural Woodwork
- 06 50 00 – Structural Plastics
- 06 60 00 – Plastic Fabrications
These sections must be current and consistently referenced throughout the construction division 01 guide: general requirements process. A single outdated section number in a construction division 01 guide: general requirements deliverable can trigger RFIs, scope disputes, and rework downstream.
Who Does Division 06 Work in This Workflow
- Specification writers authoring Division 01 — engages with Division 06 – Wood, Plastics, and Composites sections during construction division 01 guide: general requirements to ensure wood, plastics, and composites scope is correctly classified and coordinated.
- Project managers reviewing spec completeness — engages with Division 06 – Wood, Plastics, and Composites sections during construction division 01 guide: general requirements to ensure wood, plastics, and composites scope is correctly classified and coordinated.
- Architects ensuring drawing-to-spec coordination — engages with Division 06 – Wood, Plastics, and Composites sections during construction division 01 guide: general requirements to ensure wood, plastics, and composites scope is correctly classified and coordinated.
- Contractors reviewing project requirements before bidding — engages with Division 06 – Wood, Plastics, and Composites sections during construction division 01 guide: general requirements to ensure wood, plastics, and composites scope is correctly classified and coordinated.
These professionals depend on accurate Division 06 data to produce deliverables that align with the project manual and avoid classification conflicts across disciplines.
How Standards Support Division 06 in Construction Division 01 Guide: General Requirements
Construction standards govern how Division 06 sections are organized, cross-referenced, and maintained within the construction division 01 guide: general requirements workflow:
MasterFormat — Defines the Division 01 section structure—from Summary of Work through Closeout Procedures—that governs administrative requirements for the entire project.
SectionFormat — Ensures each Division 01 section follows consistent Part 1/Part 2/Part 3 structure where applicable.
Division 06 Cross-References
UniFormat: Division 06 maps to UniFormat B (Shell) for wood framing, C (Interiors) for casework and millwork, and B10 for mass timber superstructure.
OmniClass: OmniClass Table 23 (Products) classifies lumber, engineered wood, and composite products used across Division 06 sections.
These governed relationships ensure that Division 06 data stays aligned with element classifications and lifecycle tags throughout the construction division 01 guide: general requirements workflow. When cross-references break, coordination failures multiply across every trade and discipline that touches wood, plastics, and composites work.
CSI Dynamic Standards for Division 06 in Construction Division 01 Guide: General Requirements
CSI Dynamic Standards includes Division 06 as part of a connected, edition-aware classification system—licensed through The Construction Standard. For teams executing construction division 01 guide: general requirements, this means always-current Division 06 section numbers and titles, governed cross-references to UniFormat and OmniClass, and edition tracking that prevents the classification errors that cascade through construction division 01 guide: general requirements deliverables. Instead of manually verifying that Division 06 references are up to date at each workflow step, teams get a single source of truth that stays current across every project.
Access Current CSI Standards
CSI Dynamic Standards provides authorized access to MasterFormat, UniFormat, and OmniClass through a connected, edition-aware platform. Create an account to view access options, or review pricing for organization-wide standards use.
Sources and review scope
Reviewed against CSI’s public standards information for scope, terminology, and licensing context. This public guide provides orientation and does not reproduce or replace the licensed standard. Content review date: July 31, 2026.
People also search for
Explore closely related CSI divisions, standards, and construction classification topics.
Ready to Get Started?
CSI Dynamic Standards includes MasterFormat, UniFormat, and OmniClass as a connected, edition-aware system. The Construction Standard provides licensed access—built for the speed of your work.
123 N Pitt St. Suite 450
Alexandria, VA 22314info@theconstructionstandard.com